ENDORSEMENTS
Comments From Our Customers
Steve Chesney, Custom/Repair Manager, Golfers Warehouse
(Hartford, CT)
"In our custom and repair shop we install over 26,000 grips per
year using
Brampton's HF-100 grip solvent with great success. We find that
we use less solvent to install grips than we did with mineral
spirits and other solvents we have experimented with. It is also
odorless and does not dry out our skin. Most importantly , it
dries very fast allowing our customers to play their freshly
regripped clubs usually within an hour! You can easily install a
grip even without tape!
We also install over 1,800 shafts per year using Brampton's 5/10
and 20/20 epoxy.We are so confident in the bond that we use the 5/10 for 98% of
our reshafting! Again our customers benefit by being able to get
their club back sooner- we recommend that they wait 24hrs,but
our die-hards have been known to hit their drivers an hour after
being epoxied without failure.
I strongly recommend the use of Brampton products."
Players Choice Golf Components (AZ)
"Our customers are very satisfied with the Brampton products.
The products are described by our customers as very high quality
clubmaking supplies."
Sonartec Golf (CA)
"We have been using the Brampton Pro-Fix 5 & 10 and the
HF-100 grip tape activator for a number of years. We find that
these products are very easy to work with in our busy
manufacturing environment."
CUSTOM CLUB GOLF (NC)
"WE HAVE USED THE BRAMPTON TECHNOLOGY
HF-100 AND THE PRO-FIX PRODUCTS FOR A NUMBER OF YEARS IN OUR
CUSTOM CLUB OPERATION. WE ARE VERY PLEASED WITH THE PERFORMANCE
AND EASE OF CLEANUP. THEY ARE THE BEST PRODUCTS THAT WE HAVE
FOUND."
Alan Peskett,
Director, Diamond Golf International Ltd (England)
"As well as distributing Brampton products since 2001
throughout Europe, we at Diamond Golf also use the HF-100 and
Pro-Fix products in our own workshop for all golf club
assembly and repair work.The Brampton range of products is far
superior to any other epoxy or solvent I have used in 16 years
of clubmaking!"
Alternatives to Today's Grip Solvents
By Bob Dodds, PCS Journal
"The HF-100 is a new grip solvent, which the manufacturer claims
has the following properties; it's non-toxic, it's
non-flammable, it's odorless and it's effective with all
standard grips. The manufacturer also talks about a small amount
of lanolin being present in the formulation, which they claim
will normally do away with the need for gloves while installing
grips. From my testing in the new Technical Workshop here at PCS
headquarters, I can say that the above claims are justified.
This solvent is very pleasant to work with compared to some of
the chemical solvents of the past. One of the benefits of the
HF-100 is that is should be very economical to use because much
less of it is needed than with the solvents you are familiar
with."
A Safer Way
to Get a Grip
By Nils Nelson, "Red's Approach", Links Profile
"Thanks to Brampton Technology Ltd, installing grips is no
longer the pain in the neck it's been since the demise of
easy-to-use but toxic chlorinated solvents. Just over a year
ago, Brampton quietly introduced HF-100, an odorless,
non-flammable, non-toxic "solution" to the problem of putting on
grips. While many club builders and OEMs may use compressed air
to install grips, just as many rely on any number of solvents
that are often severely restricted by law.I've been disappointed with the citrus-based grip solvents
available form component companies. When I heard about HF-100, I
called Brampton to learn more........"
"HF-100 is
a non-toxic, non-flammable, odorless, colorless and is easy to
use. My one-quart sample arrived in a spray bottle. Two or three
sprays on the tape-wrapped shaft and one spray into the mouth of
the grip, and - presto! - on it went. If anything, one is
tempted to overuse The Solution at first because you can't
believe so little is needed. If any should fall into your
catch-pan, HF-100 is reusable."
|
